20 search results

• Software / Linux / Command Line
  How do I remove all lines from a file up to a keyword?
  To remove all lines up to and including a keyword from a file simply use sed as follows: sed '1,/keyword/d' infile ...
• Hardware / Cluster HAT / Cluster CTRL
  How do I write new firmware to Cluster Triple?
  Control of the Cluster Triple is done using an ATmega328P (or ATmega328PB), the IC can be reprogrammed using either a standard ...
• Hardware / Cluster HAT / Cluster CTRL
  How do I use the solder jumpers on the Cluster HAT?
  Solder jumpers on the Cluster HAT allow you to modify the default behaviour and configuration. To change the configuration you ...
• Hardware / Cluster HAT / Cluster CTRL
  How do I write new firmware to Cluster Stack?
  Control of the ClusterCTRL Stackis done using an ATmega328P (or ATmega328PB), the IC can be reprogrammed using either a standard ...
• Hardware / Cluster HAT / Cluster CTRL
  How do I write new firmware to Cluster Triple
  Control of the Cluster Triple is done using an ATmega328P (or ATmega328PB), the IC can be reprogrammed using either a ...
• Hardware / Cluster HAT / Cluster CTRL
  How do I write new firmware to Cluster Stack
  Control of the ClusterCTRL Stackis done using an ATmega328P (or ATmega328PB), the IC can be reprogrammed using either a standard ...
• Hardware / VoIP
  How do I factory reset a Siemens Gigaset A580IP / C475IP / S685IP
  To remove all settings from the phone (It will revert back to DHCP and a default pin of 0000).   Remove the ...
• Software / Hosting Control Panels
  Why is cPanel is showing disk usage when the account has no database?
  Sometimes cPanel does not remove the database correctly and leaves behind files.   Take a backup and then remove the files in   /var/cpanel/datastore/<username>/   Then ...
• Software / Microsoft Windows
  Unable to start Virtual PC "host processor type mismatch or lack of hardware-assisted virtualization support
  To start your virtual machines when you recieve the error "<machine> could not be restored because of either host processor type ...
• Software / Linux / Command Line
  How do I disable NetworkManager?
  If you want to configure your network devices manually via /etc/network/interfaces you can remove the service. Firtstly configure your network ...
• Hardware / Cluster HAT / Cluster CTRL
  ClusterCTRL: How to write an image to the eMMC?
  To write an image to the eMMC on a Compute Module you need to boot it as a USB Device ...
• Software / Linux / Command Line
  ClusterCTRL: How do I USBBOOT a Compute Module and use eMMC as local storage/swap?
  A Compute Module will boot as a USB device if either USBBOOT is enabled or it can't find bootcode.txt in ...
• Software / Linux / Manuals
  Manual: vi
  PROLOG This manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface may differ (consult the ...
• Hardware / Mobile
  Android phone on Three - data has stopped working with 3G.
  On the Three network you must use 3G for data access, sometimes the APN profiles can cause problems and they ...
• Hardware / Cluster HAT / Cluster CTRL
  [LEGACY] Guide to using the RPIBOOT [test] image on the Cluster HAT/Zero Dongle / Zero
  See the current documentation on booting without SD cards, this legacy information is kept here in case it helps anyone.   Cluster ...
• Hardware / Cluster HAT / Cluster CTRL
  How do I USBBOOT Pi Zero/Pi Zero 2 without SD cards (Cluster HAT/Cluster CTRL)?
  With the Cluster CTRL images (linked from the ClusterHAT website) it's now possible to mix/match booting nodes (Pi Zeros/Compute Modules/A+) ...
• Software / Linux
  How do I resize a disk image (Raspbian SD/USB image)?
  To resize the last partition in a disk image, for example a Raspberry Pi SD card image first increase the ...
• Software / Linux / Command Line
  How are nodes numbered with Cluster CTRL/Cluster HAT (resolve order conflict)?
  The pX number of a node for control is set by it's priority (this might not be the same as ...
• Hardware / Cluster HAT / Cluster CTRL
  Troubleshooting missing Pi Zeros in a ClusterHAT
  If you've got the Cluster HAT connected and you're having problems with one or more Pi Zeros not being visible ...
• Hardware / Cluster HAT / Cluster CTRL
  How do I update the firmware on ClusterHAT v2.6?
  The ClusterHAT v2.6 uses an ATtiny1616 to emulate the XRA1200P I/O expander, to update the firmware using the built-in UPDI programmer ...